火焰偵測系統 Flame Detector

 
 

回首頁

簡介

設備

設計

測試

數據

無線系統

保養

E-mail

留言版

氣體偵測器

 

 

 

 

 

 

    Flame-test  
 
1. Measures of site before sensor test
 
1) Break the alert system : In case of site test after installation of detector, the alert system may cause intermittent contact to site. Warning! not to intermittent.
2) Report for site cooperation previously : Test fire on site, sometimes it would denied because of worry about disturbance to operation. So, request the cooperation first with the post in charge.
 
2. Method of performance test of sensor
Relation between set up time and operate
The fire alert is activated with long term more than set up.
For example, the sensor what set 5second term is no action with 4second fire.
With no alert and blinking LED lights means it is sensing flame.
Attention - The condition is not allow to make fire, Do not site test.
 
1) Test with lighter

Method of test

Use this method ordinary when you want to test simply in 1~3 meter. in this case the distance is affected by sensitivity.
 
2) Simple Test with torch

Method of test

Use this method ordinary in site when you want to operation test in 5~10 meter. The flame which made by torch is maintained longer than set up, it makes fire alert system activate. In this case, sensitivity is belong the size of flame.

also, the blue flame from torch is too small, then upside down the torch and shake it to make yellow flame and make it as large as to sense.
activation of sensor belongs
① Sensitivity setting
② Delay time (setting time)
③ Distance between sensor and flame.
④ Size of flame. so make fire at least optimal level to sensing.
 
3) The test method with fire plane

Method of test

① The case of testing within the range of nominal sensing distance.
(Use plane size 33cm(W) x 33cm(L) x 5cm(H))
Usually the case is incongruent to test with lighter or torch, then it needs the flame size that using fire plane is filed with fuel and its combustion. According to the rules of KOFEIS(KOrea Fire Equipment Inspection Standard) from Korea Fire Equipment Inspection Corporation, the sensor's activation is allowed over the fixed standard otherwise, failure.

The point of attention is, it needs enough water supplying and enough gap under the plane to cut off the heat transfer while testing. (It needs our consultation.)

② The case of testing almost maximum nominal sensing distance.
(Use plane size 70cm(W) x 70cm(L) x 5cm(H))

Test in same condition with #①. If the fire of small plane (33cm(W) x 33cm(L) x 5cm(H)) is not enough to sense in this distance, then use lager fire from lager one(70cm(W) x 70cm(L) x 5cm(H)) according to the rules of KOFEIS.
(Not only lager one but also small one can test activation.)
 
4) Test with our tester
    - If you have problems to test with fire, then use our tester.
 
UV/IR test lamp - sensing range : Max. 5m
Control method
  Turn on the switch after check the battery.
  Fix the direction of tester to sensor.
  Check the activation of sensor.
IR3 test lamp - sensing range : Man. 5m
Control method
Turn on the switch after check the battery.
  Fix the direction of tester to sensor.
  Check the activation of sensor.
   
IR3 long range test lamp(FS-20) - sensing range : Max. 20m
Control method
  Turn on the switch.
(outdoor - battery, indoor - use outlet (220V))
  Warm up the tester works smooth after turn it on.
  Turn on the CHOPPER switch. (Check the voltmeter at 4V)
  Fix the direction of tester to sensor.
  Check the activation of sensor.
The tester using flame (FS-10)
Control method
  Install the flame tester in angle of sensor's.
  Ignite the gas nozzle.
  Check the activation of sensor.
 
 
   
 

   

 
  ISO9001   ISO14001
 
 
           
  RFD-2000X
火焰偵測器
RFD-3000X
火焰偵測器
RFD-2T
 火焰偵測器
RFD-2TN-I
火焰偵測器
RFD-2FT
 火焰偵測器
RFD-2FTN
火焰偵測器
 
           
  RFD-2FT5-I
火焰偵測器
RFD-2FTN-I
火焰偵測器
RFD-3T-I
火焰偵測器
RFD-3FT
火焰偵測器
RFD-3FT-I
 火焰偵測器
Type-P-Class1-Receiver
 
           
  RMD-5T
火焰偵測器
RMD-3T
火焰偵測器
RFD-IRS
火焰偵測器
SUN
火焰偵測器
TL205
火焰偵測器
TL305
火焰偵測器
 
           
  FS-10 PSU-05 PSU-20 AIR BK-1 PSU-20-01
 

名發科技有限公司  電話07-803-8232   傳真   網址:http://mingfa.tw